Top Dog Promotions $12,500 Purse April 10th 11th Owenton Ky

[ky49]

Top Dog Promotions (SPRING-SMASH) Big Car Pro Stock Championship!! April 10th and April 11th Owenton Ky
April 11th 7pm! Ispection Starts at 1pm! All inspected by 6pm
$12,500 Purse/ 60 Car Limit
Big Car Pro Stock 80 & Newer (NO 03 and UP)
Pre Entry Fresh Car Only!!! (CLASS IS FULL) 60 Cars!
1st $7,000
2nd $2,500
3rd $1,000
4th $500
Maddog $500
(CALL IF INTERESTED IN GETTING ON THE WAITING LIST)

Vendors that are setting up and sponsoring product are!!
1. Ultra Fab Derby Shop/ Ultra Beads Aaron Lyons/ Darin Culver Ky
2. SKI inc./ Trans. Prot. Ryan Songalewski Michigan
3. BuzzKill Rubber Co. Ryan Kehl Indiana
4. M-1 Extreme Josh Lee Indiana
5. Destruction Addicts Derby Products Jammie Jones NC
6. Slade Speed Shop Nick King Ohio
7. Cheater's Video Robert Compton Illinois
8. Crash N Bash Derby Gear Travis Brinson Ky
9 Crash Course Derby Podcast Chris Marquart & Josh Decker NY
MORE SPONSORS AND VENDORS TO ANNOUNCE

Mini Van/ Mini Truck Bone Stock Class $50 Entry 15 Spot (Full) Pre Registered!! (CLASS IS FULL)
$750 Plus Trophies

Circle Track invite only from Friday's show!! 10 Cars!!

Kids Power Wheels $10
All kids get trophies ( Trophies sponsored by Ryan Songalewski of Ski Inc)

NO REFUNDS ON ILLEGAL CARS!!! NO Spots can be sold
Inspection starts at 1pm and cars need to be inspected by 6pm. Derby starts at 7pm

Gates Open at 12pm $10 gate fee kids under 5 are free!! Drivers Pay at gate
NO PIT PASSES!!! IT IS FREE ROAM!!!

Great show in the works drivers from 5 states and vendors from 7 states!!!! Make sure you don't miss this!!!
ALL TOP DOG PROMOTION RULES APPLY!!

Questions Contact Holly Bowling or
John 859-393-8693

FRIDAY APRIL 10TH Owenton Ky 7pm
Bone Stock "Winshield" Class 20 CAR LIMIT!!!
ONE SHOT DEAL!! Pre Register $50 Entry Fee (CLASS IS FULL)
1st $1200
2nd $500
3rd $200
Maddog $100
DRIVERS LIST SOON!!

Rules for "Bone stock Class"
2015 Windshield Bone Stock Class Rules 1980 and newer
1 Car has to be factory!!! You cant change ANYTHING. Only exceptions are....
2 Must remove glass and plastic from cars
3 You can run any tire
4 You can weld rear ends
5 Wire doors, trunk,and hood in 6 spots. 3 strands at each point.
6 Gas tank and battery can be moved into the floor boards but have to be secured!
7 NO CREASING THE BODY OR FRAME!!
8 Frame can be notched
9 Square Body bumpers on square body cars! Bubble Top bumpers on bubble tops!!
10 Bumpers can be welded on. Single pass weld only!
11 One single bar can be welded behind the seat. Has to be with in 12" of seat. NO EXCEPTIONS! Max bar is 4" x 4" with a 6" end plate!
12 Headers are ok!
DO NOT CHANGE ANYTHING ELSE!!
Any Questions call FIRST!

Mini Car Circle Track Race $40 Entry $500 purse
Only the TOP TEN CARS get to race Saturday!!!
Then we will do another purse for Saturday night!!
We had to do this for time and to give you guys some extra time to race Friday!!!

Lawn Mower Derby $30 Entry 100% Pay Back and a Free Event Shirt on Saturday if you pre enter!!

ALL TOP DOG RULES APPLY and ALL RULES WILL BE POSTED SOON!!
This event is Sponsored by
Owen Co. Fair Board/ Top Dog Promotions
Any questions contact Holly Bowling
John 859-393-8693

[mrporkchop]

Cant wait should b a awesome show with some of the best drivers in the nation

[ky49]

2015 TOP DOG PROMOTIONS PRO STOCK CLASS RULES!!! Includes
APRIL 11th $11,000 Owenton Ky show 50 Car limit!!
1. Any 1980 or newer sedan or wagon. NO 03 and Ups!!
2. Helmet with eye protection and seat belt must be worn at all times.
3. 5 mph limit Pit speed at all times.
4. Top 3 cars are subject to re-inspection.
5. Any controversies or protest must be brought up before drivers meeting.
6. ANY QUESTIONS CALL FIRST, IF IT DOESN'T SAY YOU CAN DO IT, DON'T DO IT!
7. All decisions are final.
8. All glass, plastic, and interior must be removed before arriving at the derby.
9. Motor swaps are allowed.
10. You can weld motor mounts to the frame and run a lower engine cradle.
Motor can be chained straight down to cradle only! With one bolt no welding of links!
11.*NEW (A) If you run a mid plate set up between Trans and Motor.. You can have a 4 bar floating cage.It cant connect to the frame or floor at any point. At no point in time can the tranny protector come in contact with the cage or parts.The dash bar must be 6 inches from the firewall and 6 inches from the Top of hump in floor board with no alterations.. Back bar has to be within 12" of the front seat. Roll over bars are preferred.
(B) If you run without a mid plate set up...You are aloud to have the Dash Bar That runs across the Top of the Trans protector. It CANNOT BE CONNECTED TO IT OR SLEEVED IN ANY WAY. It can only lay on it and the dash bar can be connected to the 2 side bars. Dash Bar CANNOT be welded to the fire wall.
YOU CAN ONLY RUN (A)or(B) NOT BOTH!!Anyone else can run 4 Bar floating cage.
12. You can change body bolts to 1/2 inch and body mounts can be changed but the body mounts or washers cannot be welded to the frame.
13. NO distributor protector at all! OR HALO ON MOTOR! You can have a gas tank protector that cant be any wider than 24"! NO EXCEPTIONS! It cant be bolted or welded at any point to the rear seat area!
14. Battery must be moved to passenger side floor board and covered.
15. Gas tank must be moved to back seat area and covered.
16. You can weld 3 inches wide 5 inches on 5 inches off all the way around the door. No solid door welding!
17. Trunk lids, right and left side weld 5 inches on 5 inches off. Front and back of trunk lid, may be wired in only 2 spots each. 3 strands of wire on each.
18. Hood can be bolted or wired in 6 places, no angle iron on fenders and hood.
19. Bumpers can be any year and interchange. Bumpers can also be welded on. The bumper seems can also be welded. You can add a 4" wide 1/2" thick 24" long piece to the center of bumper on top or the front side!
20. Bumper can only be 22" in front and no lower than 16" in the back.
21. Car suspension must have bounce, not just in tires. No Solid Suspensions!
22. You can change rear ends, and you can run any rear end.You can also run any trailing arms on rear end.
23. You can put 2 bolts in fenders with a 2" washer on the outside.
24. No welding on the frame. No plates on the frame anywhere. Only place being welded should be motor mounts and bumpers or specified.
25. Must run factory FORD vic,lincoln,or merc TIE ROD and TIE ROD ENDS! NO EXCEPTIONS!! You can weld the factory slit. "opening"
26. On pre-ran cars only, you can weld 1-3 inch by 5 inch plate ¼ inch thick per frame rail, where it is bent or broken. NOT FOR APRIL 11th
27. NO frame shaping but you can hammer in spots that are blown out on pre-ran cars.
28. You can have 2 strands of wire from core support to the top of the front bumper (not in front of radiator) 2 strands of wire to the back bumper.
29. Tires round and black.
30. You must call me on any repair for pre-ran cars or rust in fresh cars!!!
31. You can run no larger than a 4” spacer on core support for fan clearance and the spacer cannot be welded to the frame. NO EXCEPTIONS!!
32. You can run ¾ inch all thread in front core support through the hood.
33. You can run a transmission protector with steel bell, but the protector has to stay around the transmission, it cannot brace against the back of motor/heads or cross member. (no kickers to these) or off of these!!!
34. You cannot move or add any body mounts!
35. You can cut the front of frame rail off to the first mount and that's it!!!!! YOU CANT MOVE OR RE-WELD THE FIRST BODY MOUNT BACK ON! HAS TO STAY IN FACTORY LOCATION!
36. YOU CAN PITCH a CAR BY CUTTING THE FRONT FLAP ONLY!!!! ONE SINGLE PASS RE-WELDING AND NO ADDED METAL AND NO WELDING IN THE BOXES!!! NO COLD BENDING ANYWHERE ELSE!!! Pitch limited because of 4" core support spacer and NO OTHER spacers can be added!! NO EXCEPTIONS!!!!
37. You can run slider shafts!
38. You can run a different cross member but keep the mounting point on the frame to less than 5 inches.
39.You may crease the body but all seems need to be seen to check for welds.
40. You must run factory bumper shocks or no shocks. NO homemade bumper shocks!
41. No added metal or welding to any part of frame or car unless specified!!
Anything added for strength will be cut!! Sway Bars mounted factory to frame!
42. Roll Bars have to be straight up and over ad with in 12" of seat!
43 A- arms have to remain in stock location. Cant be moved forward or backward
44.Hood Washer can not exceed 4" in diameter!
45 You can run aftermarket spindles
46 Transmission can only be mounted in one place!! It CANT BE BRACED OR HAVE KICKERS OR HAVE EARS TO THE CROSS MEMBER!! ONE MOUNTING POINT IN CENTER!!!
47. NO SKID PLATE (tranny or motor) can be used for strength! Or it will be cut!
48 NEW FRONT BUMPER PLATE! You can ADD a 4" wide 1/2" thick 24" long piece to the center of the bumper! Either on the top or front side of bumper.
49 BUILD TO THESE RULES NOT ABOVE THEM! OR YOU WONT RUN!!
50 NO GREY AREAS LEFT OVER FROM LAST YEAR!! NEW YEAR!!!
51 NEW RULE FOR APRIL 11TH ONLY!! You can have 2- kickers FROM THE DASH BAR TO THE BACK SIDE OF A-arms!! The kickers can be welded to frame only! Not to A-arms! No plate on frame. 2"x 2" square tubing only as kickers!
Top Dog Promotions is not responsible for lost, stolen, or damaged items or property at any event.
Top Dog Promotions is not responsible for any accidents, or injuries of any type at any event.
Top Dog Promotions reserves the right to reject any entry for any or no reason.
Rules may be edited or clarified at anytime! ALWAYS CALL WITH QUESTIONS!
Any questions contact: John Peck 859-393-8693

[ky49]

The Big Car Stock Class is full at this time!! Thanks and this show is going to be one of the best!!

[ky49]

The class is full at 60 cars!! Great show!

[ky49]

I would like to invite each and every Top Dog Promotions fan and driver to listen in for a big announcement regarding Spring Smash (April 10-11) in Owenton, KY. It will be made live on the air by The
Crash Course Derby Podcast show Monday night 6pm Eastern. Dont Miss IT!!
Chris Marquart, Josh Decker, Brian Tomkins, Ben Haust, Crash Course Podcast/

[ky49]

Vendors that are setting up and sponsoring product are!!
1. Ultra Fab Derby Shop/ Ultra Beads Aaron Lyons/ Darin Culver Ky
2. SKI inc./ Trans. Prot. Ryan Songalewski Michigan
3. BuzzKill Rubber Co. Ryan Kehl Indiana
4. M-1 Extreme Josh Lee Indiana
5. Destruction Addicts Derby Products Jammie Jones NC
6. Slade Speed Shop Nick King Ohio
7. Cheater's Video Robert Compton Illinois
8. Crash N Bash Derby Gear Travis Brinson Ky
9 Crash Course Derby Podcast
Josh Decker Chris Marquart New York
10. Brian Nerat Steel tail housing/converter fan/Hardened yoke! Wisconsin
11 Brian's Machine Shop 3/8 weld centers and a set of solid motor mounts. Ky
12. Roy Turner (Roy's Rears) Ohio
13. All new NDDA will be set up and accepting memberships!! Holly Bowling Ky
14 James Wilson Rottie Motorsports Indiana
15 Big Booty Transmission Clay Meredith (Transmission) Ky
16 Derbytees.com Mark Klein (Free shirts to winners) Illinois.
MORE SPONSORS AND VENDORS TO ANNOUNCE

Its going to be a great show! Don't miss out!

[ky49]

A couple days away!!! All the top notch vendors and a awesome list of drivers....DON'T MISS THIS ONE!!

[ky49]

The Owenton Ky Demo Derby April 10th and 11th is rain or shine!!! The derby starts at 7pm and inspection Saturday is from 1pm to 6pm. Gate admission is $10 kids under 5 are free. The Fair grounds address is 355 Ellis Rd Owenton Ky 40359.
Questions contact John 859-393-8693 or Holly 502-514-1495