Tell City, IN (July 5, 2014)

[HotWired Customs]

2014 Perry County 4-H Fair
DEMOLITION DERBY
Address for Fairgrounds: Indiana 66, Tell City, IN 47586

Saturday July 5th @ 7PM (cst)


STOCK BIG CARS
MODIFIED BIG CARS
MINI CARS
LAWNMOWERS

$30 Entry Fee for all classes



NO RAIN CHECKS OR REFUNDS.
ALL ANOUNCEMENTS THE DAY OF THE EVENT SUPERSEDE ALL OTHERS.

FOR MORE INFORMATION CALL
ERIC ADKINS 270-316-8171.

[HotWired Customs]

MODIFIED CARS

1. ANY YEAR CAR SEDAN OR WAGON, NO IMPERIALS OR PRE 73 LINCOLNS
2. ANY MOTOR/TRANS/DRIVESHAFT/ REAR-END
3. DISTRIBUTOR/TRANNY/REAR-END PROTECTORS ALLOWED. NO FRAME PROTECTORS ON REAR ENDS ALLOWED.
4. CROSS MEMBERS NO BIGGER THAN 2”X4” TUBING AND MAXIMUM 6” ANGLE FOR MOUNTING CROSS MEMBER TO THE FRAME.
5. A 4 BAR CAGE MAXIMUM 6IN. IS ALLOWED WITH 4 KICKERS WELDED TO SHEET METAL ONLY. CAGE MAY BE INSIDE THE DOORS. DOOR BARS CAN NOT EXCEED MORE THAN HALFWAY TO THE REAR DOOR.
6. ROLL OVER BAR IS MANDATORY. MUST BE STRAIGHT UP AND DOWN AND MAY BE WELDED TO FRAME
7. GAS TANK PROTECTORS ARE ALLOWED NO WIDER THAN 30”. WELDED TO SHEET METAL ONLY, BUT YOU CANNOT BEAT SHEET METAL BACK TO FRAME RAILS. PROTECTOR MUST BE WELDED OFF THE REAR SEAT BAR; CAN NOT BE MOUNTED TO FLOORBOARD.
8. YOU MAY RUN EITHER A KICKER TO THE DISTRIBUTOR PROTECTOR OR TWO KICKERS FROM DASH BAR TO REAR OF A-ARMS 2INCH TUBING MAX. ONE OR THE OTHER KICKER; NOT BOTH. NOTHING INNOVATED OR YOU WILL CUT OFF!!
9. BODY BOLTS MAY BE CHANGED ¾” BOLTS MAX. BODY SPACERS 3 INCH MAX. YOU MAY TACK WELD THEM IN PLACE; THEY MUST CENTER HOLE, NO OFFSETTING OF SPACERS. YOU MUST HAVE SPACERS, NO BOLTING BODY DOWN SOLID. ALL BODY BOLTS AND WASHER MUST BE INSIDE FRAME. YOU MAY ADD ONE EXTRA BODY MOUNT BUT MUST MEET BODY BOLT RULES.
10. YOU MAY WELD TOP AND BOTTOM FRAME SEAMS BOX FORWARD ONE PASS ONLY.
11. ANY FRONT BUMPER IS ALLOWED, YOU CAN USE SQUARE TUBING FOR BUMPER, NO SHARP PROTRUDING POINTS, IF BUMPER ANGLE IS MORE THAN FACTORY YOU WILL CUT OFF. BUMPER MAY NOT STICK OUT PAST FENDERS. BUMPER SHOCKS NO LARGER THAN 2”X 12” TUBING. BUMPER SHOCKS MUST BE INSIDE FRAME. BUMPER HEIGHT 24” MAXIMUM TO TOP OF THE BUMPER.
12. DOOR AND TRUNK SEAMS MAY BE WELDED SOLID USING 3” X ¼” MAX. STRAP. YOU MAY SKIN THE DRIVERS DOOR FOR ADDED PROTECTION.NO OTHER DOORS PLATED ON FRESH CARS
13. TRUNK LIDS AND QUARTER PANELS MAY BE BEAT DOWN, NO ADDING OF METAL. ALL QUARTERS WILL BE DRILLED IN INSPECTION FOR ADDED METAL.
14. SUSPENSION MAY BE SOLID, YOU CAN STRAP WELD A-ARMS TO FRAME 3” WIDE STRAP MAX. YOU MAY USE 1- 3”X 3” STRAP ON BOTTOM A ARM, STRAIGHT ½ WAY ON FRAME.
15. SWAY BAR CAN BE BOLTED TO LOWER A ARM AND MAY BE WELDED TO BOTTOM OF FRAME 4” MAXIMUM STRAP OR TUBING.
16. HUMP PLATES ALLOWED BUT MUST BE NO LONGER THAN 22 INCHES AND WILL BE MEASURED IN THIS FORM 11 INCHES FROM CENTER OF HUMP TO REAR OF CAR AND 11 INCHES TO FRONT ANY MORE IN EITHER DIRECTION YOU WILL CUT!!!!
17. BODY CREASING, ENHANCING OF EXISTING BODY LINES IS ALLOWED, BUT NO FOLDING OVER SEAMS AND WELDING.
18. CORE SUPPORT BOLTS 1 INCH MAX. AND MAY RUN THRU HOOD. 2”X 2” TUBING OR PIPE MAXIMUM ON SPACERS.
19. YOU MAY WELD 2”X2” ANGLE ON TOP RADIATOR SUPPORT NO WIDER THAN RADIATOR OPENING.
20. YOU MAY PITCH, TILT OR TIP FRONT-ENDS BUT NO ADDED METAL IN ANY WAY!!!!
21. YOU MAY BOLT HOOD DOWN IN SIX PLACES, IF USING ANGLE 6 INCHES MAX.
22. CARS MUST HAVE FRONT WINDOW BAR, YOU MAY ALSO RUN ONE WINDOW BAR IN CENTER OF TRUNK CAN NOT ATTACH TO ROLL OVER BAR & CAN NOT BE FURTHER BACK THAN 4” FROM WHERE BOTTOM OF BACK GLASS WAS.
23. YOU MAY USE ANY STOCK TYPE REAR BUMPER. REAR BUMPER MAY BE LOADED. YOU CAN TILT REAR BUMPER AND MAY BOX IN REAR FRAME. PLATES CAN NOT EXCEED MORE THAN 3” ON FRAME. BOTTOM OF BUMPER CAN NOT BE LOWER THAN 16”.
24. AFTERMARKET BRAKE PEDALS, GAS PEDALS, TRANNY COOLERS CAN NOT BE MOUNTED TO STREGTHEN THE CAR IN ANY WAY.
25. PRE-RAN CARS MAY USE 4 – 4X4 IN. ¼” MAX. THICKNESS PLATES TO REPAIR BENT FRAME; PLATES MAY NOT BUTT AGAINST ONE ANOTHER. IT MUST BE OBVIOUS IT NEEDED THE PLATE.
26. NO PATCHING OF SHEET METAL OTHER THAN THE FRONT TWO DOORS ON PRE-RANS
27. PRE-RAN CARS MUST MEET MINIMUM BUMPER HEIGHT REQUIREMENTS.


STOCK BIG CAR

1. ANY YEAR CAR. NO IMPERIALS, PRE 73 LINCOLNS, HEARSES OR CHECKERED CABS.
2. ALL CARS MUST BE STRIPPED CLEAN.
3. ALL BODY BOLTS MUST REMAIN STOCK EXCEPT CORE SUPPORT BOLTS AND THE TWO REAR MOUNTS BY THE BUMPER. ,YOU MAY USE 5/8 BOLTS MAX. IN THESE TWO LOCATIONS ONLY.
4. YOU MAY USE A 3 INCH SPACER IN THE CORE SUPPORT WITH ALL-THREAD GOING THRU HOOD, THE REAR BOLTS MAY NOT GO THRU TRUNK.
5. DOORS MAY BE WIRED OR WELDED SHUT IN TWO PLACES PER SEAM. IF WELDING PLATES NO LARGER 3”X3”X1/4” MAXIMUM.
6. TRUNKS OR REAR DOORS ON WAGONS MAY BE WIRED OR WELDED IN 8 PLACES PLATES. PLATES NO LARGER THAN 3”X3”X1/4”.
7. YOU MAY BEAT TRUNK DOWN OR V CENTERS OF TRUNK BUT QUARTER PANELS MUST REMAIN STRAIGHT. SPEAKER DECK MUST REMAIN IN CAR. TRUNK MUST HAVE A 12” INSPECTION HOLE. NO REAR WINDOW BAR ALLOWED.
8. YOU MUST HAVE A 4 BAR CAGE. YOU MAY RUN BARS INSIDE DOORS. DOOR BARS CANNOT EXTEND PAST FRONT FIREWALL AND 12” BEHIND POST, DASH BAR MUST BE 5” FROM FIREWALL AND 5” FROM FLOORBOARD.
9. YOU MUST HAVE A ROLL OVER BAR MOUNTED TO EITHER DOOR BAR OR REAR SEAT BAR, CANNOT MOUNT TO FLOOR OR FRAME. MUST BE MOUNTED STRAIGHT UP AND DOWN.
10. A GAS TANK PROTECTOR IS ALLOWED NO WIDER THAN 30” AND CANNOT TOUCH FLOOR BOARD AND MUST BE 6” FROM REAR SEAT PAN.
11. ANY MOTOR OR TRANSMISSION YOU MAY RUN A LOWER ENGINE CRADLE AND WIRE OR CHAIN MOTOR DOWN BUT MUST USE EXISTING BOLT. NO DISTRIBUTOR OR PULLEY PROTECTORS ALLOWED.
12. YOU MAY USE AFTERMARKET MOTOR MOUNTS, NO EXCESSIVE WELDING.
13. MUST USE FACTORY CROSS MEMBER FOR MAKE OF CAR. NO WELDING OF CROSS MEMBER AND MUST USE FACTORY BOLTS.
14. STOCK TYPE CAR REAR ENDS, GEARS AND AFTER MARKET AXLES OK, BUT NO BRACES OR PROTECTORS ON REAR-ENDS.
15. REAR TRAILING ARMS MUST BE STOCK. NO ADDED METAL
16. TIE RODS MUST REMAIN STOCK. NO ADDED METAL
17. SUSPENSION MUST REMAIN STOCK, CAR HAS TO BOUNCE
18. BUMPER HEIGHT 21” MAX AND 16” MIN.
19. ANY CAR BUMPER ALLOWED MAY BE SEAM WELDED, BUT NO LOADING OF BUMPERS. YOU MAY WELD BUMPER STRAIGHT TO FRAME. BUMPER SHOCKS MAY BE COMPRESSED AND WELDED. MUST BE BUMPER SHOCK FOR TYPE OF CAR RUNNING.YOU MAY SHORTEN FRONT FRAME RAIL TO CORE SUPPORT MOUNT.NO RELOCATING MOUNT!
20. YOU MAY NOTCH FRAME OR DIMPLE FRAMES FOR CONTROLLING BENDS ONLY. BUT NO PRE-BENDING
21. YOU MAY COLD TILT FRONT ENDS BUT NO CUTTING OF WELDS. COLD BEND ONLY!!! NO WELDING!!!
22. SHEET METAL MAY BE CREASED AT LOCATION WHERE FRAME IS NOTCHED, BUT NO CREASING OF BODY LINES
23. HOODS MAY BE BOLTED OR WIRED IN 6 LOCATIONS IF USING ANGLE NO LARGER THAN 6”
24. YOU MAY RUN AFTERMARKET STEERING COLUMN.
25. YOU MAY RUN ENGINE AND TRANSMISSION COOLERS.
26. YOU MAY RUN AFTERMARKET GAS PEDALS, BRAKE PEDALS, TRANNY COOLERS BUT THEY CAN NOT STREGTHEN CAR IN ANY WAY.
27. ANY WHEEL/TIRE 15” OR SMALLER.
28. NO WELDING ON FRAMES OTHER THAN MOUNTING BUMPERS OR MOTOR MOUNTS.
29. NO SLIDER DRIVE SHAFTS.
30. NO HUMP PLATES.



MINI CARS
1. FRONT WHEEL DRIVE ONLY, 105” WHEELBASE MAX.
2. ALL GLASS, CHROME, MOLDINGS, REAR SEATS AND FACTORY GAS TANKS MUST BE REMOVED
3. HELMET, SEATBELT AND EYE PROTECTION MUST BE WORN AT ALL TIMES
4. GAS TANKS MUST BE RELOCATED BEHIND DRIVERS SEAT, SECURELY FASTENED AND COVERED
5. GAS TANK PROTECTORS ARE ALLOWED, BUT THEY CANNOT STRENGTHEN CAR IN ANYWAY, THEY MAY REST AGAINST REAR SEAT DECK BUT YOU CANNOT BEAT SHEET METAL BACK
6. 4 OR 6 CYLINDERS ALLOWED. FRONT WHEEL DRIVE ONLY.
7. DOORS,TRUNKS/HATCHES MAY BE WELDED SOLID, 3” MAX.
8. YOU MAY WELD FROM STRUT TOWERS FORWARD AND CORE SUPPORT SEAMS ONE PASS ONLY. NO ADDED METAL
9. BUMPER SHOCKS CANNOT EXCEED 12” LONG 2” MAX. DIAMETER
10. ANY BUMPER MAY BE USED BUT NO SHARP PROTRUDING POINTS (OR YOU WILL CUT OFF)
11. ALL CARS MUST HAVE A 4 POINT CAGE, DOOR BARS NOT TO EXCEED 12” PAST DOOR POST. YOU MUST HAVE A ROLL-OVER BAR, CAGE MATERIAL NOT TO EXCEED 6” YOU MAY PLATE OUTSIDE OF DRIVER DOOR SKIN.
12. YOU MUST HAVE A FRONT WINDSHIELD BAR OR #9 WIRE. YOU MAY HAVE A REAR WINDOW BAR, CANNOT GO 6” PAST SPEAKER DECK TRUNK SEAM
13. IF RUNNING AN ELECTRIC FUEL PUMP IT MUST HAVE A SHUT OFF SWITCH
14. BUMPER HEIGHT 21” MAX. 16” MIN.
15. NO PATCHING OF SHEET METAL EXCEPT DRIVER OR PASSENGER FRONT DOORS
16. PRE RAN CARS MAY PLATE BENDS WITH FOUR 3”X3” PLATES CAR MUST BE BENT AND PLATES CANNOT BUTT AGAINST ANOTHER.



LAWN MOWERS

1. MOWER MUST BE AN AVAILABLE MOWER . NO HOMEMADE FRAMES
2. NO REAR ENGINE MOWERS ALLOWED
3. ENGINE MUST BE FACTORY LAWNMOWER ENGINE (BRIGGS ETC… ETC…)
4. TRANSAXLES MUST BE FACTORY AVAILABLE MOWER TRANS AXLES & REAREND YOU MAY WELD SPIDER GEARS
5. ENGINE BAY RE-ENFORCING IS ALLOWED BUT MUST BE CONTAINED INSIDE OF HOOD AND MAINTAIN FACTORY BODY LINES
6. ALL MOWERS MUST RUN A HOOD AND FENDERS, HOOD MUST BE SCREWED, WIRED OR WELDED TO DASH PANEL AROUND DRIVERS AREA
7. MOWERS MUST HAVE WORKING BRAKES
8. GAS TANKS MUST BE SECURELY MOUNTED
9. LEG GUARDS ARE MANDATORY AND MUST BE BOLTED OR WELDED FROM REAR FENDER TO FRONT OF FOOT REST OR FRAME
10. A REAR BUMPER IS PERMITTED BUT MAY NOT EXTEND MORE THAN 4IN. OUT, IT MUST STAY INBETWEEN THE TIRES
11. NO SHARP OR PROTRUDING OBJECTS
12. YOU MAY CHANGE PULLEYS TO INCREASE SPEED
13. MOWERS MUST USE LAWN MOWER TYPE WHEELS AND TIRES, THEY CAN BE GROOVED FOR TRACTION, NO TIRE CHAINS OR DUALS ALLOWED
14. BATTERY MUST BE REMOVED AFTER STARTING MOWER FOR HEAT
15. NO FRONT BUMPERS
16. NO MOWER DECKS
17. YOU MAY REINFORCE GRILL AREA TO HIT WITH, BUT MUST BE 6 IN. OFF THE GROUND AND A SMOOTH SURFACE
18. ALL DRIVERS MUST HAVE LONG PANTS, LONG SLEEVE SHIRTS, HELMET AND SAFETY GLASSES TO COMPETE
19. IF LEG GUARDS ARE NOT DEEMED SAFE YOU WILL NOT RUN!!!! USE TUBING, ANGLE, CHANNEL OR PIPE....NOTHING ELSE