maddog
Junior Member
Posts: 62
|
Post by maddog on Jun 24, 2013 0:52:02 GMT -5
July 20th STOCK BIG CARS 1st 1500 & trophy 2nd 400 & trophy 3rd 100 & trophy Top dog promotions is putting it on I found the rules on the Franklin County fair web page correct me if im wrong but here are the rules!
|
|
maddog
Junior Member
Posts: 62
|
Post by maddog on Jun 24, 2013 0:52:50 GMT -5
BIG CAR STOCK 1. Any 1980 or newer sedan or wagon. 2. Helmet with eye protection and seatbelt must be worn at all times. 3. 5 mph limit Pit speed at all times. 4. Top 3 cars are subject to re-inspection. 5. Any controversies or protest must be brought up before drivers meeting. 6. ANY QUESTIONS CALL FIRST, IF IT DOESN‘T SAY YOU CAN‘T DO IT, DON‘T DO IT! 7. All decisions are final. 8. All glass, plastic, and interior must be removed before arriving at the derby. 9. Motor swaps are allowed. 10. You can weld motor mounts to the frame and run a engine cradle. 11. You can weld a four bar cage not allowed to touch the floor or frame at any point. Back bar has to be within 12” of the front seat. Roll over bars are preferred. 12. Must have stock body bushings and bolt size. 13. No distributor protector or gas tank protector, you can have a gas tank holder that is no closer than 8 inches from back seat area. 14. Battery must be moved to passenger side floor board and covered. 15. Gas tank must be moved to back seat area and covered. 16. Welding of door seams, below the window weld 5 inches on 5 inches off. No solid welding of door strips, no welding above window. 17. Trunk lids, right and left side weld 5 inches on 5 inches off. Front and back of trunk lid, may be wired in only 4 spots. 3 strands of wire on each. 18. Hood can be bolted or welded in 6 places, no angle iron on fenders and hood. 19. Bumpers can be any year and interchange. Bumpers can also be welded on. Bumper seems cannot be welded. 20. Bumper can only be 22” in front and no lower than 16” in the back. 21. Car suspension must have bounce, not just in tires. 22. You can change rear ends, and you can run any rear end. 23. You can put 2 bolts in fenders with a 2” washer on the outside. 24. No welding on the frame. No plates on the frame anywhere. Only place being welded should be motor mounts and bumpers or specified. 25. Must run factory tie rods, but can weld the seem closed. 26. On pre-ran cars only, you can weld 1-3 inch by 5 inch plate ¼ inch thick per frame rail, where it is bent or broken. 27. NO frame shaping but you can hammer in spots that are blown out on pre-ran cars. 28. You can have 2 strands of wire from core support to the top of the front bumper (not in front of radiator) 2 strands of wire to the back bumper. 29. Tires round and black. 30. You must call me on any repair for preran cars. 31. You can run no larger than a 3” spacer on core support for fan clearance and the spacer cannot be welded to the frame. 32. You can run ¾ inch all thread in front core support through the hood. 33. You can run a transmission protector, but the protector has to stay around the transmission, it cannot brace against the back of motor/heads or cross member. Top Dog Promotions is not responsible for lost, stolen, or damaged items or property at any event. Top Dog Promotions is not responsible for any accidents, or injuries of any type at any event. Top Dog Promotions reserves the right to reject any entry for any or no reason. Any questions contact: John Peck 859-393-8693
|
|