Hawesville, KY (Hancock County Fair) (8/17)

[HotWired Customs]

Hancock County Fair Demolition Derby
Hawesville, Ky

August 17, 2013

Time: 7 pm CST

MOWERS
MINI CARS
STOCK BIG CARS
MODIFIED BIG CARS



IF YOU STRETCH OR BEND A RULE YOU WILL LOSE THAT RULE, BUILD TO RULES! ANY QUESTIONS CALL:
(270-316-8171) ERIC ADKINS

[HotWired Customs]

MODIFIED CARS

1. ANY YEAR CAR SEDAN OR WAGON, NO IMPERIALS OR PRE 73 LINCOLNS
2.ANY MOTOR/TRANS/DRIVESHAFT/CAR TYPE REAR-END
3.DISTRIBUTOR/TRANNY/REAR-END PROTECTORS ALLOWED
4.A 4 BAR CAGE MAXIMUM 6IN. IS ALLOWED WITH 4 KICKERS WELDED TO SHEET METAL ONLY
5.ROLL OVER BAR IS MANDATORY AND MAY BE WELDED TO FRAME
6.GAS TANK PROTECTORS ARE ALLOWED WELDED TO SHEET METAL ONLY, BUT YOU CANNOT BEAT SHEET METAL BACK TO FRAME RAILS
7.YOU MAY RUN EITHER A KICKER TO THE DISTRIBUTOR PROTECTOR OR TWO KICKERS FROM DASH BAR TO REAR OF A-ARMS 2INCH TUBING MAX.ONE OR THE OTHER KICKER NOT BOTH. NOTHING INNOVATED OR YOU WILL CUT OFF!!
8.BODY BOLTS MAY BE CHANGED ¾ BOLTS MAX. BODY SPACERS 3 INCH MAX. YOU MAY TACK WELD THEM IN PLACE, THEY MUST CENTER HOLE, NO OFFSETTING OF SPACERS. YOU MUST HAVE SPACERS, NO BOLTING BODY DOWN SOLID. YOU MAY ADD ONE EXTRA BODY MOUNT BUT MUST MEET BODY BOLT RULES.
9.YOU MAY WELD TOP AND BOTTOM FRAME SEAMS BOX FORWARD ONE PASS ONLY.
10.ANY BUMPER IS ALLOWED, YOU CAN USE SQUARE TUBING FOR BUMPER BUT MUST BE WRAPPED IN CHROME, NO SHARP PROTRUDING POINTS AND MAY NOT STICK OUT PAST FENDERS. NO BUMPER SHOCKS LARGER THAN 2”X 12” TUBING.
11.DOOR AND TRUNK SEAMS MAY BE WELDED SOLID USING 3IN. MAX. STRAP. YOU MAY SKIN THE DRIVERS DOOR FOR ADDED PROTECTION.NO OTHER DOORS PLATED ON FRESH CARS
12.TRUNK LIDS AND QUARTER PANELS MAY BE BEAT DOWN, NO ADDING METAL, IF SUSPECTED OF ADDED METAL YOU WILL BE CUT AT END OF NIGHT AND FORFEIT ALL MONEY
13. SUSPENSION MAY BE SOLID, YOU CAN STRAP WELD A-ARMS TO FRAME 3IN. WIDE STRAP MAX. MAXIMUM. YOU MQY USE 1- 3”X 3” STRAP ON BOTTOM A ARM, STRAIGHT ½ WAY ON FRAMS BUMPER HEIGHT 24 IN. 16 IN. MINIMUM HEIGHT TO BOTTOM OF BUMPER
14. HUMP PLATES ALLOWED BUT MUST BE NO LONGER THAN 22 INCHES AND WILL BE MEASURED IN THIS FORM 11 INCHES FROM CENTER OF HUMP TO REAR OF CAR AND 11 INCHES TO FRONT ANY MORE IN EITHER DIRECTION YOU WILL CUT!!!!
15. BODY CREASING, ENHANCING OF EXISTING BODY LINES IS ALLOWED, BUT NO FOLDING OVER SEAMS AND WELDING.
16. CORE SUPPORT BOLTS 1 INCH MAX. AND MAY RUN THRU HOOD
17. YOU MAY PITCH , TILT OR TIP FRONT-ENDS BUT NO ADDED METAL IN ANY WAY!!!!
18. YOU MAY BOLT HOOD DOWN IN SIX PLACES, IF USING ANGLE 6 INCHES MAX.
19. CARS MUST HAVE FRONT WINDOW BAR, YOU MAY ALSO RUN REAR WINOW BAR, BUT MAY NOT BE FURTHER BACK THAN 4 IN. FROM WHERE BOTTOM OF BACK GLASS WAS
20. PRE-RAN CARS MAY USE 4 – 4X4 IN. ¼ MAX. THICKNESS PLATES TO REPAIR BENT FRAME,PLATES MAY NOT BUTT AGAINST ONE ANOTHER. IT MUST BE OBVIOUS IT NEEDED THE PLATE.
21. PRE-RAN CARS MUST MEET MINIMUM BUMPER HEIGHT REQUIREMENTS.
22.PRE-RAN CARS MAY PATCH DRIVER AND PASSENGER FRONT DOORS ONLY!!! ANY OTHER PATCHING OF SHEET METAL YOU WILL CUT OFF.

STOCK BIG CAR

1.ANY YEAR CAR NO IMPERIALS OR PRE 73 LINCOLNS
2.CARS MUST BE STRIPPED CLEAN
3.A BODY BOLTS MUST REMAIN STOCK EXCEPT CORE SUPPORT AND TWO REAR MOUNTS,YOU MAY USE 5/8 BOLTS MAX.IN THESE TWO LOCATIONS ONLY.
4.YOU MAY USE A 3 INCH SPACER IN THE CORE SUPPORT WITH ALL-THREAD GOING THRU HOOD,THE REAR BOLTS MAY NOT GO THRU TRUNK
5.DOORS MAY BE WIRED OR WELDED SHUT IN TWO PLACES PER SEAM,IF WELDING PLATES NO LARGER THAN 3X3
6.TRUNKS OR REAR DOORS ON WAGONS MAY BE WIRED OR WELDED IN 8 PLACES PLATES NO LARGER THAN 3X3
7.YOU MAY BEAT TRUNK DOWN OR V CENTERS OF TRUNK BUT ¼ PANELS MUST REMAIN STRAIGHT.
8.YOU MUST HAVE A 4 BAR CAGE,DOOR BARS CANNOT EXTEND 12IN.PAST FRONT DOORS,DASH BAR MUST BE 5IN.FROM FIREWALL AND 5IN.FROM FLOORBOARD
9.YOU MUST HAVE A ROLL OVER BAR MOUNTED TO EITHER DOOR BAR OR REAR SEAT BAR,CANNOT MOUNT TO FLOOR OR FRAME
10.A GAS TANK PROTECTOR IS ALLOWED NO WIDER THAN 30INCHES AND CANNOT TOUCH FLOOR BOARD AND MUST BE 6INCHES FROM REAR SEAT PAN.
11.ANY MOTOR OR TRANSMISSION YOU MAY RUN A LOWER ENGINE CRADLE AND WIRE OR CHAIN MOTOR DOWN BUT MUST USE A EXISTING BOLT.NO DISTRIBUTOR OR PULLEY PROTECTORS.
12.STOCK TYPE CAR REAR ENDS, GEARS AND AFTER MARKET AXLES OK,BUT NO BRACES OR PROTECTORS ON REAR-ENDS
13.REAR TRAILING ARMS MUST BE STOCK NO ADDED METAL
14.TIE RODS MUST REMAIN STOCK NO ADDED METAL
15.SUSPENSION MUST REMAIN STOCK,CAR HAS TO BOUNCE
16.BUMPER HEIGHT 21 IN. MAX.16 IN.MIN
17.ANY CAR BUMPER ALLOWED MAY BE SEAM WELDED,BUT NO LOADING OF BUMPERS,YOU MAY WELD BUMPER STRAIGHT TO FRAME,BUMPER SHOCKS MAY BE COMPRESSED AND WELDED MUST BE BUMPER SHOCK FOR TYPE OF CAR RUNNING.YOU MAY SHORTEN FRONT FRAME RAIL TO CORE SUPPORT MOUNT.NO RELOCATING MOUNT!
18.YOU MAY NOTCH FRAMES BUT NO PRE-BENDING
19.SHEET METAL MAY BE CREASED AT LOCATION WHERE FRAME IS NOTCHED,BUT NO CREASING OF BODY LINES
20.HOODS MAY BE BOLTED OR WIRED IN 6 LOCATIONS IF USING ANGLE NO LARGER THAN 6 IN.
21.YOU MAY RUN ENGINE AND TRANSMISSION COOLERS
22.ANY WHEEL/TIRE 15IN.OR SMALLER
23.NO WELDING ON FRAMES OTHER THAN MOUNTING BUMPERS


MINI CARS
1.FRONT WHEEL DRIVE ONLY,105IN.WHEELBASE MAX.
2. ALL GLASS, CHROME, MOLDINGS ,REAR SEATS AND FACTORY GAS TANKS MUST BE REMOVED
3.HEMET,SEATBELT AND EYE PROTECTION MUST BE WORN AT ALL TIMES
4.GAS TANKS MUST BE RELOCATED BEHIND DRIVERS SEAT, SECURELY FASTENED AND COVERED
5.GAS TANK PROTECTORS ARE ALLOWED, BUT THEY CANNOT STRENGTHEN CAR IN ANYWAY,THEY MAY REST AGAINST REAR SEAT DECK BUT YOU CANNOT BEAT SHEET METAL BACK
6.4 OR 6 CYLINDERS ALLOWED. FRONT WHEEL DRIVE ONLY.
7.DOORS,TRUNKS/HATCHES MAY BE WELDED SOLID,3 INCH MAX.
8.YOU MAY WELD FROM STRUT TOWERS FORWARD AND CORE SUPPORT SEAMS ONE PASS ONLY. NO ADDED METAL
9.BUMPER SHOCKS CANNOT EXCEED 12INCHES LONG 2 INCH MAX. DIAMETER
10.ANY BUMPER MAY BE USED BUT NO SHARP PROTRUDING POINTS (OR YOU WILL CUT OFF)
11.ALL CARS MUST HAVE A 4 POINT CAGE, DOOR BARS NOT TO EXCEED 12 INCHES PAST DOOR POST. YOU MUST HAVE A ROLL-OVER BAR, CAGE MATERIAL NOT TO EXCEED 6 IN. YOU MAY PLATE OUTSIDE OF DRIVER DOOR SKIN.
12.YOU MUST HAVE A FRONT WINDSHIELD BAR OR #9 WIRE. YOU MAY HAVE A REAR WINDOW BAR, CANNOT GO 6 INCHES PAST SPEAKER DECK TRUNK SEAM
13.IF RUNNING A ELECTRIC FUEL PUMP IT MUST HAVE A SHUT OFF SWITCH
14.BUMPER HEIGHT 21IN.MAX.16IN.MIN.
15.NO PATCHING OF SHEET METAL EXCEPT DRIVER OR PASSENGER FRONT DOORS
16.PRE RAN CARS MAY PLATE BENDS WITH FOUR 3 X3 PLATES CAR MUST BE BENT AND PLATES CANNOT BUTT AGAINST ANOTHER.


TRUCKS

1.ANY AMERICAN 1/2 OR 3/4 TON TRUCK OR SUBURBAN ALLOWED,NO 4WHEEL DRIVES
2. MOTOR SWAPS ALLOWED
3. FUEL TANKS MUST BE MOUNTED SECURELY IN BED
4. DOORS MAY BE WIRED OR WELDED 3 IN. MAX. STRAP
5.CAB AND BED MOUNTS MAY BE CHANGED WITH ¾ BOLTS 5 INCH MAX,. WASHERS
6. TAILGATES MAY BE WELDED SOLID, AND YOU MAY FOLD OVER BED SIDES
7.A CAGE MUST BE BUILT INSIDE CAB FOR DRIVERS SAFETY ROLL OVER BAR IS MANDATORY!!!!!!!!!!!!!!
8.YOU MUST EITHER BOLT OR WELD BED TO THE CAB
9. YOU MAY USE BUMPER OF CHOICE BUT NO EXTREME POINTS OR YOU WILL CUT OFF!
10. HOODS MAY BE BOLTED OR WIRED IN 6 SPOTS
11. NO ADDING METAL TO FRAMES
13. NO SPLIT RIMS


LAWN MOWERS

1. MOWER MUST BE AN AVAILABLE MOWER ( NO HOMEMADE FRAMES
2. NO REAR ENGINE MOWERS ALLOWED
3. ENGINE MUST BE FACTORY LAWNMOWER ENGINE ( BRIGGS ETC… ETC…
4. TRANSAXLES MUST BE FACTORY AVAILABLE MOWER TRANS AXLES & REAREND YOU MAY WELD SPIDER GEARS
5. ENGINE BAY RE-ENFORCING IS ALLOWED BUT MUST BE CONTAINED INSIDE OF HOOD AND MAINTAIN FACTORY BODY LINES
6. ALL MOWERS MUST RUN A HOOD AND FENDERS,HOOD MUST BE SCREWED,WIRED OR WELDED TO DASH PANEL AROUND DRIVERS AREA
7. MOWERS MUST HAVE WORKING BRAKES
8. GAS TANKS MUST BE SECURELY MOUNTED
9. LEG GUARDS ARE MANDATORY AND MUST BE BOLTED OR WELDED FROM REAR FENDER TO FRONT OF FOOT REST OR FRAME
10. A REAR BUMPER IS PERMITTED BUT MAY NOT EXTEND MORE THAN 4IN. OUT,IT MUST STAY INBETWEEN THE TIRES
11. NO SHARP OR PROTRUDING OBJECTS
12. YOU MAY CHANGE PULLEYS TO INCREASE SPEED
13. MOWERS MUST USE LAWN MOWER TYPE WHEELS AND TIRES,THEY CAN BE GROOVED FOR TRACTION, NO TIRE CHAINS OR DUALS ALLOWED
14. BATTERY MUST BE REMOVED AFTER STARTING MOWER FOR HEAT
15. NO FRONT BUMPERS
16. NO MOWER DECKS
17. YOU MAY REINFORCE GRILL AREA TO HIT WITH, BUT MUST BE 6 IN. OFF THE GROUND AND A SMOOTH SURFACE
18. ALL DRIVERS MUST HAVE LONG PANTS,LONG SLEEVE SHIRTS,HELMET AND SAFETY GLASSES TO COMPETE
19. IF LEG GUARDS ARE NOT DEEMED SAFE YOU WILL NOT RUN!!!! USE TUBING,ANGLE,CHANNEL OR PIPE....NOTHING ELSE

[adkins35]

Hawesville will have lawnmowers,mini cars,stock big cars,modified big cars and trucks

[adkins35]

Show starts at 7 see ya there!