Post by HotWired Customs on Jun 19, 2012 21:35:07 GMT -5
July 21, 2012
6:00 pm
Nelson County Fairgrounds (just off the Bluegrass parkway)
2391 New Haven RD.
Bardstown, KY 40004
Payouts, 1st,$1200 2nd,$700 3rd,$300
RULES for Big Cars
1. Any year cars are allowed
2. Remove all fiberglass and plastic panels, all glass including windshield. Remove all molding, rear seats, hood latches, factory gas tank, ALL WHEEL WEIGHTS and door handles.
3. Only welding on the frame is A arms forward and mounting bumper, motor mounts, repairs or rewelding from where you notched or prebent.
4. Bumpers should be welded, chained, bolted or all. Bumper can not be no higher than 22 inches. It can be welded directly to frame, bumpers swaps are allowed. No home made bumpers.
5. Rear frame rail no lower than 14 inches at rear bumper. Body bolts can be changed. No washers more than 3 inches round any size bolt allowed, bolts must be inside of frame.
6. Doors and trunks can be welded solid with 3" wide no thicker then 1/4 metal.
7. Four bar interior cage is allowed. May not contact frame, firewall, motor or transmission or extend more than 12 inches behind driver seat. No bar up to firewall from dash bar (this means no kickers at all) roll bar must be straight up and down in center of driver’s compartment.
8. Hood may be wired or bolted in six places. No wire in front of radiator. Max 9 gauge wire, fan must be coverd at all times.
9. Trunk or roof may be stuffed down.
10. Two vertical wires or bars 1/2" thick 3" wide for front window bars, may not contact motor in any way.
11. Gas tank is to be placed in backseat area, gas tank protectors are allowed no wider than 24" may not be bolted or weled to frame.
12. Suspension may be solid, all thread for shocks are ok, NO PLATES TO CONTROL BENDING OF FRAME.
13. Tires – round and black.
14. Only one battery allowed, secured and covered.
15. Engine swap is allowed, must have 15"X15" hole in hood.
16. Fuel pump must have shut off switch if electric.
17. Core support can be bolted all the way thourgh with 1" all thread.
18.Two 8x8 holes must be cut in trunk 3" from were trunk is welded to the quaters.
19. No interior seam welding on body panels.
20. Body must have 1 inch space between frame.
21. Frame can be repaired with 4X4 1/4" patch maximum 6 plates an only if we can see clear evidence of frame damage. So just call first. If it isn’t bent don’t fix it.
22. Frame creasing is allowed
23. Rear window bar is allowed 3" wide 1/2" thick, welded 3" past were trunk meets speaker deck, no more then 3" bolted or welded to roof.
24. : Distributor guard and 22" hump plates are allowed that is 22" at widest point, with the center located at the center of the hump and no thicker than 1/4".
25. Wedgeing is allowed
26. 12" bumper shocks, inside the frame or out, not both!!! no bigger then 2" tubing or pipe.
27. Rearends can be swapped, no leaf conversions, unless the car was factory that way, must be 5 lug, any bracing must be within 5" of rearend, and not touch frame.
28. Slip shafts are allowed.
29. Engine proctectors are allowed, Two 3/8 chains on each side welded to frame no more then 3 links can be welded.
30. Sway bar can be welded or bolted solid to frame.
31. Frame must be 23" from spring pocket to back side of bumper.
32. You may pitch front frame rails, by cutting box loose and rewelding.
33. 03 a newer fords if replacing k member it must be welded like the factory donar car was no staggering, wheel base must be the same.
34. No skining of body panels.
35. If it's not in the rules call first!!
Any qustion's call:
Tommy Crask 502-827-4091
Tyler Brangers 270-268-1289
Andy Wardrip 270-945-5204
6:00 pm
Nelson County Fairgrounds (just off the Bluegrass parkway)
2391 New Haven RD.
Bardstown, KY 40004
Payouts, 1st,$1200 2nd,$700 3rd,$300
RULES for Big Cars
1. Any year cars are allowed
2. Remove all fiberglass and plastic panels, all glass including windshield. Remove all molding, rear seats, hood latches, factory gas tank, ALL WHEEL WEIGHTS and door handles.
3. Only welding on the frame is A arms forward and mounting bumper, motor mounts, repairs or rewelding from where you notched or prebent.
4. Bumpers should be welded, chained, bolted or all. Bumper can not be no higher than 22 inches. It can be welded directly to frame, bumpers swaps are allowed. No home made bumpers.
5. Rear frame rail no lower than 14 inches at rear bumper. Body bolts can be changed. No washers more than 3 inches round any size bolt allowed, bolts must be inside of frame.
6. Doors and trunks can be welded solid with 3" wide no thicker then 1/4 metal.
7. Four bar interior cage is allowed. May not contact frame, firewall, motor or transmission or extend more than 12 inches behind driver seat. No bar up to firewall from dash bar (this means no kickers at all) roll bar must be straight up and down in center of driver’s compartment.
8. Hood may be wired or bolted in six places. No wire in front of radiator. Max 9 gauge wire, fan must be coverd at all times.
9. Trunk or roof may be stuffed down.
10. Two vertical wires or bars 1/2" thick 3" wide for front window bars, may not contact motor in any way.
11. Gas tank is to be placed in backseat area, gas tank protectors are allowed no wider than 24" may not be bolted or weled to frame.
12. Suspension may be solid, all thread for shocks are ok, NO PLATES TO CONTROL BENDING OF FRAME.
13. Tires – round and black.
14. Only one battery allowed, secured and covered.
15. Engine swap is allowed, must have 15"X15" hole in hood.
16. Fuel pump must have shut off switch if electric.
17. Core support can be bolted all the way thourgh with 1" all thread.
18.Two 8x8 holes must be cut in trunk 3" from were trunk is welded to the quaters.
19. No interior seam welding on body panels.
20. Body must have 1 inch space between frame.
21. Frame can be repaired with 4X4 1/4" patch maximum 6 plates an only if we can see clear evidence of frame damage. So just call first. If it isn’t bent don’t fix it.
22. Frame creasing is allowed
23. Rear window bar is allowed 3" wide 1/2" thick, welded 3" past were trunk meets speaker deck, no more then 3" bolted or welded to roof.
24. : Distributor guard and 22" hump plates are allowed that is 22" at widest point, with the center located at the center of the hump and no thicker than 1/4".
25. Wedgeing is allowed
26. 12" bumper shocks, inside the frame or out, not both!!! no bigger then 2" tubing or pipe.
27. Rearends can be swapped, no leaf conversions, unless the car was factory that way, must be 5 lug, any bracing must be within 5" of rearend, and not touch frame.
28. Slip shafts are allowed.
29. Engine proctectors are allowed, Two 3/8 chains on each side welded to frame no more then 3 links can be welded.
30. Sway bar can be welded or bolted solid to frame.
31. Frame must be 23" from spring pocket to back side of bumper.
32. You may pitch front frame rails, by cutting box loose and rewelding.
33. 03 a newer fords if replacing k member it must be welded like the factory donar car was no staggering, wheel base must be the same.
34. No skining of body panels.
35. If it's not in the rules call first!!
Any qustion's call:
Tommy Crask 502-827-4091
Tyler Brangers 270-268-1289
Andy Wardrip 270-945-5204
