Post by HotWired Customs on Jun 19, 2012 13:13:17 GMT -5
2012 ADKINS MOTORSPORTS DEMOLITION DERBY RULES
MODIFIED CARS
1. ANY YEAR CAR, SEDAN OR WAGON. NO IMPERIALS OR PRE 73 LINCOLNS
2. ANY MOTOR/TRANS/DRIVE-SHAFT/ CAR TYPE REAR-END
3. DISTRIBUTOR/TRANNY/REAR-END PROTECTORS ALLOWED
4. A 4 BAR CAGE. MAXIMUM 6INCHES IS ALLOWED WITH 4 KICKERS WELDED TO SHEET METAL ONLY
5. ROLL OVER BAR IS ALLOWED AND MY BE WELDED TO FRAME
6. GAS TANK PROTECTORS ARE ALLOWED. WELDED TO SHEET METAL ONLY. YOU CANNOT BEAT SHEET METAL BACK TO FRAME RAILS
7. YOU MAY RUN KICKER TO DASH IN THIS FORM ONLY!!!! WELD A PIECE OF SQUARE TUBING OR PIPE ON DASH. THEN SLIDE A SMALLER DIAMETER TUBE OR PIPE THRU WITH A 5X5 PLATE WELDED ON THE END UP TO FIREWALL AND RUN A BOLT THRU THE TUBES. ( JUST LIKE A RECEIVER HITCH ON A TRUCK) ANY QUESTIONS CALL
8. BODY BOLTS MAY BE CHANGED. 3/4 BOLT MAX AND 3INCHES ROUND WASHERS, PUCKS OR SQUARE PLATES. YOU MAY TACK WELD THESE IN TWO PLACES TO HOLD THEM IN PLACE. THEY MUST CENTER HOLES AND MAY NOT OFFSET
9. YOU MAY WELD TOP AND BOTTOM FRAME SEAMS FROM BOXES FORWARD. ONE PASS ONLY
10. ANY BUMPER IS ALLOWED, YOU CAN USE SQUARE TUBING FOR BUMPERS BUT MUST BE WRAPPED IN CHROME. NO SHARPS PROTRUDING POINTS AND MY NOT STICK OUT PAST FENDERS
11. DOOR AND TRUNK SEAMS MAY BE WELDED SOLID USING 3INCH MAX. STRAPPING
12.TRUNK LIDS AND QUARTER PANELS MY BE BEAT DOWN. NO ADDING METAL. IF SUSPECTED PF ADDED METAL YOU WILL BE CUT AT END OF THE NIGHT AND FORFEIT ALL MONEY
13. SUSPENSION MAY BE SOLID. YOU CAN STRAP WELD A-ARMS TO FRAME. 2 INCH WIDE STRAP MAX. MAXIMUM BUMPER HEIGHT 24INCH MAX AND 16 MINIMUM HEIGHT TO BOTTOM OF BUMPER
14. HUMP PLATES ALLOWED BUT MUST BE NO LONGER THAN 22INCHES AND WILL BE MEASURED IN THE FORM. 11 INCHES FROM CENTER OF HUMP TO REAR OF CAR AND 11 INCHES TO FRONT. ANY MORE IN EITHER DIRECTION YOU WILL CUT!!!
15. BODY CREASING, ENHANCING OF EXISTING BODY LINES IS ALLOWED, BUT NO FOLDING OVER SEAMS AND WELDING.
16. CORE SUPPORT BOLTS 1 INCH MAX AND MAY RUN THRU HOOD
17. YOU MAY PITCH, TILT OR TIP FRONT-ENDS, BUT NO ADDING METAL IN ANY WAY!!!!
18. YOU MAY SHORTEN FRONT FRAME RAILS, BUT YOU MAY WELD ON SHEET METAL TO SHEET METAL ON FENDERS. NO ADDED METAL. BUMPER SHOCKS CANNOT BE FURTHER BACK THAN STOCK LOCATION
19. YOU MAY BOLT HOOD IN 6 PLACES, USING ANGLE 4 INCH MAX WIDE
20. CARS MUST HAVE FRONT WINDOW CAR. YOU MAY ALSO RUN REAR WINDOW BAR, BUT MAY NOT BE FURTHER BACK THAN 4 INCHES FROM BACK GLASS WAS
21. PRE-RAN CARS MAY USE 4 - 4X4 INCH 1/4 INCH THICK PLATES TO REPAIR BENT FRAMES. PLATE MAY NOT BUTT AGAINST ONE ANOTHER, AND MUST BE OBVIOUS IT NEEDED THE PLATE
22. PRE-RAN CARS MUST MEET MINIMUM BUMPER HEIGHT REQUIREMENTS
IF YOU STRETCH OR BEND A RULE YOU WILL LOSE THAT RULE. BUILD TO RULES!!! ANY QUESTIONS CALL ERIC AT (270-316-8171)
MINI CARS
1. 105 INCH WHEEL BASE OR LESS
2. 4 OR 6 CYL. ALLOWED
3. ANY CAR BUMPER ALLOWED
4. YOU MAY WELD OR WIRE DOORS SHUT. 3 INCH MAX STRAP
5. A 4 BAR CAGE IS ALLOWED WITH ROLL OVER BAR WELDED TO SHEET METAL ONLY
6. YOU MAY WIRE OR BOLT HOODS AND TRUNKS DOWN IN 6 PLACES
7. NO WELDING OF UNI-BODY
8. NO 4 WHEEL DRIVES
9. GAS TANKS MUST BE SECURELY MOUNTED TO FLOOR. IF ELECTRIC FUEL PUMP MUST HAVE A SHUT OFF!
TRUCKS
1. ANY AMERICAN 1/2 OR 3/4 TON TRUCK OR SUBURBAN ALLOWED. NO 4 WHEEL DRIVES
2. MOTOR SWAPS ALLOWED
3. FUEL TANKS MUST BE MOUNTED SECURELY IN BED
4. DOORS MAY BE WIRED OR WELDED. 3INCH MAX. STRAP
5. CAB AND BED MOUNTS MAY BE CHANGED WITH 3/4 BOLTS, 5 INCH MAX. WASHERS
6.TAILGATES MAY BE WELDED SOLID, AND YOU MAY FOLD OVER BED SIDES
7. A CAGE MUST BE BUILT INSIDE CAB FOR DRIVERS SAFETYROLL OVER BAR ARE ALLOWED
8. YOU MUST EITHER BOLT OR WELD BED TO THE CAB
9. STOCK TRUCK BUMPERS FRONT AND BACK
10. HOOD MAY BE BOLTED OR WIRED IN 4 SPOTS
11. NO ADDING METAL TO FRAMES
12. NO SPLIT RIMS
LAWN MOWERS
1. MOWER MUST BE AN AVAILABLE MOWER. FRAMES CAN BE REINFORCED, BUT NO HOMEMADE FRAMES
2. NO REAR ENGINE MOWERS ALLOWED
3. ENGINE MUST BE FACTORY LAWNMOWER ENGINE ( BRIGGS ETC, ETC)
4. TRANS AXLES MUST BE FACTORY AVAILABLE MOWER TRANS AXLES AND REA-REND. YOU MAY WELD SPIDER GEARS
5. ENGINE BAY RE-ENFORCEMENT IS ALLOWED BUT MUST BE CONTAINED INSIDE OF HOOD
6. ALL MOWERS MUST RUN A HOOD AND FENDERS. HOODS MUST BE SCREWED, WIRED OR WELDED TO DASH PANEL AROUND DRIVERS AREA
7. MOWERS MUST HAVE WORKING BRAKES
8. GAS TANKS MUST BE SECURELY MOUNTED
9. LEG GUARDS ARE MANDATORY AND MUST BE BOLTED OR WELDED FROM REAR FENDERS TO FRONT REST OR FRAME
10. A REAR BUMPER IS PERMITTED BUT MAY NOT EXTEND MORE THAN 4 INCHES OUT. IT MUST STAY BETWEEN TIRES
11. NO SHARP OR PROTRUDING OBJECTS
12. YOU MAY CHANGE PULLEYS TO INCREASE SPEED
13. MOWERS MUST USE LAWN MOWER TYPE WHEELS AND TIRES. THEY CAN BE GROOVED FOR TRACTION. NO TIRE CHAINS OR DUAL WHEELS
14. BATTERY MUST BE REMOVED AFTER STARTING MOWER FOR HEAT
15. NO FRONT BUMPERS. EVERYTHING MUST BE CONTAINED INSIDE FRONT WHEELS
16. NO MOWER DECKS
17. YOU MAY REINFORCE GRILL AREA TO HIT WITH, BUT MUST BE 6INCHES OFF THE GROUND AND A SMOOTH SURFACE
18. ALL DRIVERS MUST HAVE LONG PANTS, LONG SLEEVE SHIRTS, HELMET AND SAFETY GLASSES TO COMPETE
ANY QUESTION GIVE ERIC A CALL AT (270-316-8171)
SHOWS WILL HAVE
MODIFIED BIG CARS
MINIS
TRUCKS
LAWNMOWER FIGURE 8 AND DERBY
MODIFIED CARS
1. ANY YEAR CAR, SEDAN OR WAGON. NO IMPERIALS OR PRE 73 LINCOLNS
2. ANY MOTOR/TRANS/DRIVE-SHAFT/ CAR TYPE REAR-END
3. DISTRIBUTOR/TRANNY/REAR-END PROTECTORS ALLOWED
4. A 4 BAR CAGE. MAXIMUM 6INCHES IS ALLOWED WITH 4 KICKERS WELDED TO SHEET METAL ONLY
5. ROLL OVER BAR IS ALLOWED AND MY BE WELDED TO FRAME
6. GAS TANK PROTECTORS ARE ALLOWED. WELDED TO SHEET METAL ONLY. YOU CANNOT BEAT SHEET METAL BACK TO FRAME RAILS
7. YOU MAY RUN KICKER TO DASH IN THIS FORM ONLY!!!! WELD A PIECE OF SQUARE TUBING OR PIPE ON DASH. THEN SLIDE A SMALLER DIAMETER TUBE OR PIPE THRU WITH A 5X5 PLATE WELDED ON THE END UP TO FIREWALL AND RUN A BOLT THRU THE TUBES. ( JUST LIKE A RECEIVER HITCH ON A TRUCK) ANY QUESTIONS CALL
8. BODY BOLTS MAY BE CHANGED. 3/4 BOLT MAX AND 3INCHES ROUND WASHERS, PUCKS OR SQUARE PLATES. YOU MAY TACK WELD THESE IN TWO PLACES TO HOLD THEM IN PLACE. THEY MUST CENTER HOLES AND MAY NOT OFFSET
9. YOU MAY WELD TOP AND BOTTOM FRAME SEAMS FROM BOXES FORWARD. ONE PASS ONLY
10. ANY BUMPER IS ALLOWED, YOU CAN USE SQUARE TUBING FOR BUMPERS BUT MUST BE WRAPPED IN CHROME. NO SHARPS PROTRUDING POINTS AND MY NOT STICK OUT PAST FENDERS
11. DOOR AND TRUNK SEAMS MAY BE WELDED SOLID USING 3INCH MAX. STRAPPING
12.TRUNK LIDS AND QUARTER PANELS MY BE BEAT DOWN. NO ADDING METAL. IF SUSPECTED PF ADDED METAL YOU WILL BE CUT AT END OF THE NIGHT AND FORFEIT ALL MONEY
13. SUSPENSION MAY BE SOLID. YOU CAN STRAP WELD A-ARMS TO FRAME. 2 INCH WIDE STRAP MAX. MAXIMUM BUMPER HEIGHT 24INCH MAX AND 16 MINIMUM HEIGHT TO BOTTOM OF BUMPER
14. HUMP PLATES ALLOWED BUT MUST BE NO LONGER THAN 22INCHES AND WILL BE MEASURED IN THE FORM. 11 INCHES FROM CENTER OF HUMP TO REAR OF CAR AND 11 INCHES TO FRONT. ANY MORE IN EITHER DIRECTION YOU WILL CUT!!!
15. BODY CREASING, ENHANCING OF EXISTING BODY LINES IS ALLOWED, BUT NO FOLDING OVER SEAMS AND WELDING.
16. CORE SUPPORT BOLTS 1 INCH MAX AND MAY RUN THRU HOOD
17. YOU MAY PITCH, TILT OR TIP FRONT-ENDS, BUT NO ADDING METAL IN ANY WAY!!!!
18. YOU MAY SHORTEN FRONT FRAME RAILS, BUT YOU MAY WELD ON SHEET METAL TO SHEET METAL ON FENDERS. NO ADDED METAL. BUMPER SHOCKS CANNOT BE FURTHER BACK THAN STOCK LOCATION
19. YOU MAY BOLT HOOD IN 6 PLACES, USING ANGLE 4 INCH MAX WIDE
20. CARS MUST HAVE FRONT WINDOW CAR. YOU MAY ALSO RUN REAR WINDOW BAR, BUT MAY NOT BE FURTHER BACK THAN 4 INCHES FROM BACK GLASS WAS
21. PRE-RAN CARS MAY USE 4 - 4X4 INCH 1/4 INCH THICK PLATES TO REPAIR BENT FRAMES. PLATE MAY NOT BUTT AGAINST ONE ANOTHER, AND MUST BE OBVIOUS IT NEEDED THE PLATE
22. PRE-RAN CARS MUST MEET MINIMUM BUMPER HEIGHT REQUIREMENTS
IF YOU STRETCH OR BEND A RULE YOU WILL LOSE THAT RULE. BUILD TO RULES!!! ANY QUESTIONS CALL ERIC AT (270-316-8171)
MINI CARS
1. 105 INCH WHEEL BASE OR LESS
2. 4 OR 6 CYL. ALLOWED
3. ANY CAR BUMPER ALLOWED
4. YOU MAY WELD OR WIRE DOORS SHUT. 3 INCH MAX STRAP
5. A 4 BAR CAGE IS ALLOWED WITH ROLL OVER BAR WELDED TO SHEET METAL ONLY
6. YOU MAY WIRE OR BOLT HOODS AND TRUNKS DOWN IN 6 PLACES
7. NO WELDING OF UNI-BODY
8. NO 4 WHEEL DRIVES
9. GAS TANKS MUST BE SECURELY MOUNTED TO FLOOR. IF ELECTRIC FUEL PUMP MUST HAVE A SHUT OFF!
TRUCKS
1. ANY AMERICAN 1/2 OR 3/4 TON TRUCK OR SUBURBAN ALLOWED. NO 4 WHEEL DRIVES
2. MOTOR SWAPS ALLOWED
3. FUEL TANKS MUST BE MOUNTED SECURELY IN BED
4. DOORS MAY BE WIRED OR WELDED. 3INCH MAX. STRAP
5. CAB AND BED MOUNTS MAY BE CHANGED WITH 3/4 BOLTS, 5 INCH MAX. WASHERS
6.TAILGATES MAY BE WELDED SOLID, AND YOU MAY FOLD OVER BED SIDES
7. A CAGE MUST BE BUILT INSIDE CAB FOR DRIVERS SAFETYROLL OVER BAR ARE ALLOWED
8. YOU MUST EITHER BOLT OR WELD BED TO THE CAB
9. STOCK TRUCK BUMPERS FRONT AND BACK
10. HOOD MAY BE BOLTED OR WIRED IN 4 SPOTS
11. NO ADDING METAL TO FRAMES
12. NO SPLIT RIMS
LAWN MOWERS
1. MOWER MUST BE AN AVAILABLE MOWER. FRAMES CAN BE REINFORCED, BUT NO HOMEMADE FRAMES
2. NO REAR ENGINE MOWERS ALLOWED
3. ENGINE MUST BE FACTORY LAWNMOWER ENGINE ( BRIGGS ETC, ETC)
4. TRANS AXLES MUST BE FACTORY AVAILABLE MOWER TRANS AXLES AND REA-REND. YOU MAY WELD SPIDER GEARS
5. ENGINE BAY RE-ENFORCEMENT IS ALLOWED BUT MUST BE CONTAINED INSIDE OF HOOD
6. ALL MOWERS MUST RUN A HOOD AND FENDERS. HOODS MUST BE SCREWED, WIRED OR WELDED TO DASH PANEL AROUND DRIVERS AREA
7. MOWERS MUST HAVE WORKING BRAKES
8. GAS TANKS MUST BE SECURELY MOUNTED
9. LEG GUARDS ARE MANDATORY AND MUST BE BOLTED OR WELDED FROM REAR FENDERS TO FRONT REST OR FRAME
10. A REAR BUMPER IS PERMITTED BUT MAY NOT EXTEND MORE THAN 4 INCHES OUT. IT MUST STAY BETWEEN TIRES
11. NO SHARP OR PROTRUDING OBJECTS
12. YOU MAY CHANGE PULLEYS TO INCREASE SPEED
13. MOWERS MUST USE LAWN MOWER TYPE WHEELS AND TIRES. THEY CAN BE GROOVED FOR TRACTION. NO TIRE CHAINS OR DUAL WHEELS
14. BATTERY MUST BE REMOVED AFTER STARTING MOWER FOR HEAT
15. NO FRONT BUMPERS. EVERYTHING MUST BE CONTAINED INSIDE FRONT WHEELS
16. NO MOWER DECKS
17. YOU MAY REINFORCE GRILL AREA TO HIT WITH, BUT MUST BE 6INCHES OFF THE GROUND AND A SMOOTH SURFACE
18. ALL DRIVERS MUST HAVE LONG PANTS, LONG SLEEVE SHIRTS, HELMET AND SAFETY GLASSES TO COMPETE
ANY QUESTION GIVE ERIC A CALL AT (270-316-8171)
SHOWS WILL HAVE
MODIFIED BIG CARS
MINIS
TRUCKS
LAWNMOWER FIGURE 8 AND DERBY
